loading
x

MS Thread Mounted Nut

ABSSAC Precision Motion Since 1982

ABSSAC
Precision Ball Screws

Single Nut with M-thread

Backlash type/Preload type

Ballscrew Single Nut M Thread Diagram 1
Type-1: Return-plate type

Unit : mm
Ball Nut
Model number
Shaft
nominal
dia.
d
LeadBall sizeBCDLead
angle
Root dia.
d0
Number of
Circuit
Basic Load Rating
N
Nut Rigidity
N/µm
Dynamic
Ca
Static
Coa
MS 0401 B410.84.154°23'3.33.7×1560 / 350790 / 40054 / 45
MS 0602 A6216.25°52'5.12.7×1750 / 4701200 / 59058 / 49
MS 0801.5 B81.518.23°20'7.13.7×11100 / 7002200 / 110099 / 83
MS 0802 B821.58758.34°23'6.63.7×12400 / 15504100 / 2100111 / 94
MS 0802.5 Ti1j82.51.587585°41'6.33.5×12300 / -3900 / -102 / -
MS 0802.5 Ti2j82.51.587585°41'6.33.5×12300 /-3900 / -102 / -
MS 0803 A8328.36°34'6.22.7×12600 / 16504200 / 210085 / 70
MS 0804 T841.587589°03'5.92.5×11750 / -2800 / -75 / -
MS 0805 A851.58758.310°51'6.62.7×11850 / 11503000 / 150082 / 67
Ball Nut
Model number
Nut dimension
Nut typeDLL1M
MS 0401 B111174M9x0.75
MS 0602 A116.5228M14×1.0
MS 0801.5 B116.5248M14×1.0
MS 0802 B12027.57.5M16×1.0
MS 0802.5 Ti1j216.5228M14×1.0
MS 0802.5 Ti2j217.525.57.5M15×1.0
MS 0803 A12028.57.5M16×1.0
MS 0804 T216.5248M14×1.0
MS 0805 A11832.57.5M15×1.0
Basic Load Rating
N
Nut Rigidity
N/µm
Dynamic
Ca
Static
Coa
1000 / 6403300 / 1650164 / 138
   Preload type
Backlash type
Note 1)
The diameter of one of the Screw Shaft ends must be less than the Screw Shaft Root diameter,
otherwise Ball Nut cannot be installed.
Note 2)
Ball Nut dimension is without seal at the both ends. All type of Ball Nuts cannot equip with seals.
Note 3)
The Rigidity values shown in the table are theoretical values of Ball Nut Rigidity calculated from the amount of Elastic Displacement under the following conditions.
Backlash type ; Apply the Axial load equivalent to 30% of the Basic Dynamic Load Rating Ca.
Preload type ; Apply the Preload equivalent to 5% of the Basic Dynamic Load Rating Ca.
Note 4)
All models are Right-hand Screw. If Left-hand Screw is required, please ask ABSSAC representative.
Note 5)
Across Flats or drill hole is available on the Ball Nut for the convenience of assembly. Please ask ABSSAC representative.
Note 6)
Basic Load Rating or Rigidity for Backlash type and Preload type are described in the same cell.
T: +44 (0)1386 421005F: +44 (0)1386 422441E: sales@abssac.co.ukW: www.abssac.co.uk
ABSSAC
Precision Ball Screws

Single Nut with M-thread

Backlash type/Preload type

Ballscrew Single Nut M Thread Diagram 2
Type-2: Return-tube type

Unit : mm
Ball Nut
Model number
Shaft
nominal
dia.
d
LeadBall sizeBCDLead
angle
Root dia.
d0
Number of
Circuit
Basic Load Rating
N
Nut Rigidity
N/µm
Dynamic
Ca
Static
Coa
MS 1002 B1021.587510.33°32'8.63.7×12700 / 17505300 / 2700134 / 112
MS 1202 B1221.587512.32°58'10.63.7×13000 / 19006400 / 3200156 / 132
MS 1204 T1242.38112.35°55'9.82.5×13900 / -7000 / -113 / -
MS 1402 B1421.587514.32°33'12.63.7×13200 / 20007500 / 3800176 / 148
MS 1404 B1442.38114.35°05'11.83.7×15700 / 360011600 / 5800187 / 157
Ball Nut
Model number
Nut dimension
Nut typeDLL1M
MS 1002 B12327.57.5M17×1.0
MS 1202 B1253010M20×1.0
MS 1204 T225.53410M20×1.0
MS 1402 B1263010M22×1.5
MS 1404 B1303810M25×1.0
Basic Load Rating
N
Nut Rigidity
N/µm
Dynamic
Ca
Static
Coa
1000 / 6403300 / 1650164 / 138
   Preload type
Backlash type
Note 1)
The diameter of one of the Screw Shaft ends must be less than the Screw Shaft Root diameter,
otherwise Ball Nut cannot be installed.
Note 2)
Ball Nut dimension is without seal at the both ends. All type of Ball Nuts cannot equip with seals.
Note 3)
The Rigidity values shown in the table are theoretical values of Ball Nut Rigidity calculated from the amount of Elastic Displacement under the following conditions.
Backlash type ; Apply the Axial load equivalent to 30% of the Basic Dynamic Load Rating Ca.
Preload type ; Apply the Preload equivalent to 5% of the Basic Dynamic Load Rating Ca.
Note 4)
All models are Right-hand Screw. If Left-hand Screw is required, please ask ABSSAC representative.
Note 5)
Across Flats or drill hole is available on the Ball Nut for the convenience of assembly. Please ask ABSSAC representative.
Note 6)
Basic Load Rating or Rigidity for Backlash type and Preload type are described in the same cell.
T: +44 (0)1386 421005F: +44 (0)1386 422441E: sales@abssac.co.ukW: www.abssac.co.uk